Scientific blog
Archives 

Show All

  • 2015
  • 2014
  • 2013
    • December
    • November
    • October
    • September
    • August
    • July
      • PhD HK
        31/07/13
        In July I’ve worked on my next publication, entitled :” Tin-zinc alloy electrodeposition from citrate baths”. In this paper I described in details the results obtained during the firsth and the second year of my studies, when I was studying ternary system Sn(II)-Zn(II)-Mo(VI). Currently I resigne

      • core shell nanoparticles
        30/07/13
        This experiment was based on colloidal coere-shell particles with empty core and small ( 8-9nm) silver particles adsorbed on particle surface. After deposition of particles using LbL method sample was illuminated by Xenon lamp radiation for 30 min with irradiation power density of 50 mW/cm^2. Small

      • MTrybula (EMF study)
        21/07/13
        EMF measuremnt for third constant ratio of Al/Zn of molar fraction, when amount of lithium was changed from 0.1 to 0.9. Calculation of the partial excess thermodynamic properties from EMF measurement and using CAPLHAD method.
        Investigation magnetic field induced strain effect (MFIS) in single c

      • PhD report (June 2013) A.Mzyk
        13/07/13
        June was month of samples preparation for the calorimetric analysis to determine thermal stability of coatings in the temperature range from-50oC to +50oC. Similar heat treated specimens were analyzed on scanning electron microscope to assess if any changes in surface morphology took place. This mon

      • PhD report (June 2013) MG
        09/07/13
        Last month I took part in two international conferences:

        - XX Physical Metallurgy and Materials Science Conference: Advanced Materials and Technologies – AMT 2013 in Kudowa-Zdrój, where I was given an opportunity to give a speech during Young scientists session, which was entitled: “Chara

      • PhD report (June 2013) K.Kubok
        08/07/13
        My activities in June:

        During this month I have prepared publication entitled: Structural investigation of Mg-3Ca, Mg-3Zn-1Ca and Mg-3Zn-3Ca wt.% as cast alloys.

        Here you have an abstract:

        Magnesium alloys from Mg-Zn-Ca system are interesting, because of possible ap

      • PhD report (June 2013) J.Poplewska
        06/07/13
        Based on the results of the research of local orientations measured by EBSD/SEM for AA1050 and AA3004 aluminum alloys (made in the system y-x: for cross-section ND-TD or TD-ND) I made studies of transformation of these data into rolling system TD-RD and I created a tool to verify correctness of thes

      • PhD report G. Kulesza (June'13)
        05/07/13
        I decided to deal with the heat of my solutions. Cooling them were not so easy. I found that the labortory refrigerator had cooled my reagents to 17 degrees C (at room temperature over 25). The effect was pour - a little smaller pits on the surface. I'm looking for a better way of effective mix

      • PhD report July2013PC
        05/07/13
        In July let me think...Oh I forgot to mention in my previous entries that I attended the AMT Phys Metall conference in Kudowa Zdrój, where I gave a talk on the evolution of microstructure and its impact on phase transtions in Heusler Ni-Mn based alloys.
        It was well received ang gave me encourag

      • PhD JK
        04/07/13
        In June I attended international conference "XX Physical Metallurgy and Materials Science Conference Advanced Materials and Technologies AMT 2013" organised by Institute of Materials Science of Czestochowa University of Technology in Kudowa Zdrój.
        During the conference I have presente

      • June
        04/07/13
        Samples were examined by electron microscopy SEM, recording the success of EBSD map of the sample surface. The map was exported to a text file and loaded into the program Mathematica. Unfortunately, the map was created in a hexagonal grid (arrangement of pixels) and not orthogonal, hence the need to

      • June 2013/ Piotr Bobrowski
        03/07/13
        This month I was focused on learning to my exams. There were two main courses which I attended: Novel technologies in surface engineering” and “Renewable energy technologies”. Additionally, I attended a course concerning commercialization of scientific research. Most of the lectures were carried in

    • June
    • May
    • April
    • March
    • February
    • January
  • 2012
  • 2011
  • 2010